Outback-power-systems GS4048A Quick Start Guide with GSLC User Manual download pdf

CAUTION: Equipment Damage

These procedures should be done by a qualified installer who is trained on programming inverter power systems.

Failure to set accurate parameters for the system could potentially cause equipment damage. Damage caused by

inaccurate programming is not covered by the limited warranty for the system.

IMPORTANT

Check the firmware revision of all OutBack devices before use. The Radian inverter and MATE3 system display may not

communicate or operate correctly unless their firmware is above a specified revision number.

For models GS8048A and GS4048A, the firmware must be revision 001.005.xxx or higher.

The MATE3 must be revision 002.017.xxx or higher.

Quick Start Guide

900-0162-01-00 Rev A.vsd\Page-1\2014-01-24

Setup and Programming

Contact Technical Support:

Telephone: +1.360.618.4363

Email: [email protected]

Website: www.outbackpower.com

RADIAN Series

HUB 10.3

Communications

Manager

MATE3

System

Display and

Controller

Radian Inverter/Charger

GS Load Center

(GSLC)

FM80 Charge

Controllers

(x2)

WARNING: Fire/Explosion Hazard

Do not place combustible or flammable materials within 12 feet (3.7 m) of

the equipment. This unit employs mechanical relays and is not ignition-

protected. Fumes or spills from flammable materials could be ignited by sparks.

WARNING: Personal Injury

Use safe lifting techniques and standard safety equipment when working with

this equipment.

IMPORTANT:

Clearance and access requirements may vary by location. Maintaining a 36”

(91.4 cm) clear space in front of the system for access is recommended.

Consult local electric code to confirm clearance and access requirements

for the specific location.

IMPORTANT:

Not intended for use with

life support equipment.

AC Source

Utility Grid or

AC Generator

Main Electrical Panel (or overcurrent

device for the AC source)

Electrical Distribution Subpanel

(Load Panel)

Photovoltaic (PV) Array

Battery Bank

Customer-Supplied Components

Inverter/Charger

GS Load Center

System Display

and Controller

MATE3 depicted

(with FW-MB3

mounting bracket)

GS8048A

GS4048A

Radian System Products

Major Components

Optional OutBack Components

FLEXnet DC Monitor (FN-DC)

Remote Temperature Sensor (RTS)

Charge Controller

FLEXmax 80 depicted

(with FW-CCB2

mounting bracket)

PV Combiner Box PV12 depicted

Communications

Manager

HUB10.3 depicted

GSLC175-PV-120/240

GSLC175PV1-120/240

(both depicted)

EnergyCell depicted

Note: See the MATE3

manual for details on

generator control.

The MATE3 Configuration

Wizard allows quick setup of

parameters that apply to all

systems. The Configuration

Wizard is reached from the

MATE3 Main Menu as shown

to the right.

The firmware revision of all

devices can be confirmed by

navigating from the MATE3

Main Menu as shown below.

Upgrades to the firmware

revision can be downloaded

from the OutBack website

www.outbackpower.com.

Firmware Revision

Configuration Wizard

Off Grid

Grid Tied Backup

This advances the display to the

Setup Complete screen.

S S S

This advances the display to the

Setup Complete screen if the

FLEXnet DC is not installed. If the

FLEXnet DC is installed, the display

advances to the Shunt screens.

If FN-DC is installed...

Generator Installed Y

Generator Type AC Size 5.0 kW

Generator Start Manual

AUX Output Device Port 1

Back Continue

New Configuration >>

Existing Configuration >>

Restore Configuration >>

System Type Grid Tied

System Voltage 48 VDC

Array Wattage 1000

Battery Type FLA Capacity 500 Ah

Back Continue

Absorb Voltage 57.6 VDC Time 1.0

Float Voltage 54.4 VDC Time 1.0

Equalize Voltage 60.0 VDC Time 3.0

Re-Float Voltage 44.0 VDC

Back Continue

New Configuration Initialized

Back Continue

Shunt A

Connection Inverter

Back Continue

Shunt B

Connection Charge Controller

Back Continue

Shunt C

Connection Charge Controller

Back Continue

Period 1 Enable N

Weekday Use 0:00 Drop 0:00

Weekend Use 0:00 Drop 0:00

Back Continue

Period 2 Enable N

Weekday Use 0:00 Drop 0:00

Back Continue

Period 3 Enable N

Weekday Use 0:00 Drop 0:00

Back Continue

Shunt A

Connection Inverter

Back Continue

Shunt B

Connection Charge Controller

Back Continue

Shunt C

Connection Charge Controller

Back Continue

Mode Disabled

Grid Connect 48.0 VDC Delay 60 Min

Grid Disconnect 52.0 VDC Delay 60 Min

Grid Connect SOC 60% Disconnect SOC 95%

Back Continue

Shunt B

Connection Charge Controller

Back Continue

Shunt C

Connection Charge Controller

Back Continue

Period 3 Enable N

Weekday Use 0:00 Drop 0:00

Back Continue

Mode Disabled

Grid Connect 48.0 VDC Delay 60 Min

Grid Disconnect 52.0 VDC Delay 60 Min

Grid Connect SOC 60% Disconnect SOC 95%

Back Continue

Period 1 Enable N

Weekday Use 0:00 Drop 0:00

Weekend Use 0:00 Drop 0:00

Back Continue

Generator Installed N

Generator Type AC Size 5.0 kW

Generator Start Manual

AUX Output Device Port 1

Back Continue

AC Output Voltage 240 VAC

AC Phase Single

AC Input Breaker Size 50 A

Maximum Output Load 33 A

Back Continue

Period 2 Enable N

Weekday Use 0:00 Drop 0:00

Back Continue

Generator Installed N

Generator Type AC Size 5.0 kW

Generator Start Manual

AUX Output Device Port 1

Back Continue

Absorb Voltage 57.6 VDC Time 1.0

Float Voltage 54.4 VDC Time 1.0

Equalize Voltage 60.0 VDC Time 3.0

Re-Float Voltage 44.0 VDC

Back Continue

AC Output Voltage 240 VAC

AC Phase Single

AC Input Breaker Size 50 A

Maximum Output Load 33 A

Back Continue

System Type Backup

System Voltage 48 VDC

Array Wattage 1000

Battery Type FLA Capacity 500 Ah

Back Continue

Shunt A

Connection Inverter

Back Continue

AC Output Voltage 240 VAC

AC Phase Single

AC Input Breaker Size 50 A

Maximum Output Load 33 A

Back Continue

Absorb Voltage 57.6 VDC Time 1.0

Float Voltage 54.4 VDC Time 1.0

Equalize Voltage 60.0 VDC Time 3.0

Re-Float Voltage 44.0 VDC

Back Continue

System Type Off Grid

System Voltage 48 VDC

Array Wattage 1000

Battery Type FLA Capacity 500 Ah

Back Continue

Settings >>

Configuration Wizard >>

Device Data Logs >>

Event Logs >>

Firmware Update >>

System >>

Inverter >>

Charge Controller >>

Battery Monitor >>

MATE3 >>

System

System Information >>

Save / Store Information >>

Firmware Version >>

Date and Time >>

LCD Display >>

MATE3 002.017.018

1: GS8048A 001.005.002

2: GS8048A 001.005.002

Settings >>

Configuration Wizard >>

Device Data Logs >>

Event Logs >>

Firmware Update >>

Settings

Configuration Wizard

New Configuration

Masters of the Off-Grid.™

First Choice for the New Grid.

1 2 3 4

Summary of Contents

Page 1 - RADIAN Series

CAUTION: Equipment DamageThese procedures should be done by a qualified installer who is trained on programming inverter power systems. Failure to se

Page 2

Page 3

Energize/Startup ProceduresPre-startup Procedures:1. Double-check all wiring connections.2. Inspect the enclosure to ensure no debris or tools have be

Page 4 - Wiring RADIAN Series

AC SubpanelLoadsL1L2NEUGROUNDL1L2NEUGROUNDAC Source Neutral-Ground Bond56910NFM80 #2L NOUTL NGENL NGRIDFM80 #1CAT5 CableWiring RADIAN SeriesA

Comments to this Manuals

No comments

Outback-power-systems GS4048A Quick Start Guide with GSLC User Manual

Browse online or download User Manual for Power suppliers Outback-power-systems GS4048A Quick Start Guide with GSLC. Outback Power Systems GS4048A Quick Start Guide with GSLC User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Power suppliers Outback-power-systems GS4048A Quick Start Guide with GSLC