OBX-IC2024S-120/60 Owner’s ManualInstallation and OperationRugged Water ResistantInverter / Charger
8WIRE CONNECTIONSDC WiringTheInverterusesDCbrassbatteryterminalswith8Mx1.00stainlesssteelthreadedstuds.Youcanaccessthe terminals by
912 V/200 amp-hours-12 V/200 amp-hours-12 V/200 amp-hours- Voltage remains at 12 V 200 Ah + 200 Ah + 200 Ah +
106 V Battery Wiring Examples for a 24-volt system-DC DISCONNECT (FUSE OR CIRCUIT BREAKER)----SERIES: 200 amp-hours--DC DISCONNECT (FUSE OR CIRCUIT B
1112 V Battery Wiring Examples for a 24-volt system-DC DISCONNECT (FUSE OR CIRCUIT BREAKER)--SERIES: 200 amp-hours----SERIES STRING 1 CONNECTS TO INV
12AC WiringAC OUT SOCKET• — Maxicon circular molded watertight connector supplies power to the loads using the provided AC cable and plug.AC IN SOCKE
13Follow these steps to wire the Inverter to your system: Open all DC breakers or remove any fuses before connecting wiring. 1. Open all AC breakers o
14POWERING UP Once all connections are established, it is safe to turn the power on, in the following order: Connect DC power, by closing the DC break
15THE MATE2 SYSTEM CONTROLLER AND DISPLAYThe MATE serves several functions:Allows you to monitor the Inverter through a series of convenient display s
16<OFF> —turns o all Inverters connected to the MATE <SRCH> —the Inverter begins search mode if the AC load connected is smaller than all
17The AC INPUT CONTROL screen is called up, allowing the user •to connect or disconnect the Inverter to an AC input source.AC INPUT CONTROLcurrently:
OutBack Power SystemsOutBack Power Systems is a leader in advanced energy conversion technology. Our products include true sine wave inverter/chargers
18PRESS THREE TIMES: The CHARGER CONTROL screen appears. This allows the •operation of the Inverter’s battery charger to be preset for an availa
19MAIN--------------------------------12:00:30P SUM STATUS SETUP ADVThe user can press the <SUM> soft key to display the Summary screen.F
20SETUP SCREENSThe Setup screens allow you to change several settings, to make your system run more smoothly. You can program the amperage size of th
21SETUP/MATE/SUMMARY---------summary controlBACK TYPE DELAY ROLLMAIN--------------------------------12:00:30P SUM STATUS SETUP ADVSETUP
22SETUP/MATE/SUMMARY----------summary control BACK TYPE DELAY ROLLAfter selecting FX Only and exiting the SETUP/MATE/SUM/TYPE screen, the SUMMAR
23SETUP/MATE/SUMMARY/TYPE--sum screen 19 minutes delay timeBACK INC DEC SETUP/MATE/PAGE2--------------choose category:PG1 SUMRY COM MA
24•<REPOLL>forcestheMATEto“rediscover”alltheOutBackdevices it is connected to. This must be used any time an OutBack device is moved o
25Press <STATUS> on the Main menu to access the STATUS menu. STATUS contains all the meters and mode displays for OutBack products connected to
26STATUS/FX/PAGE1---------------choose categoryMODES METER BATT PG2STATUS/FX/PAGE2---------------choose categoryPG1 ERROR WARN PG3STATUS/FX/PAGE
27METER ScreensThe METER screens displays current, voltage and wattage measurements, Inverter status, and the version of Inverter software, in this or
1TABLE OF CONTENTS Welcome to the OutBack Extreme Rugged Water Resistant Inverter/Charger ...2Parts Included
28STATUS/FX/MODE-------------P00battery 27.8 vdcactualDOWN STATUS PORT STATUS/FX/METER-------------P00absorb
29STATUS/FX/PAGE2-------------------choose category: PG1 ERROR WARN PG3 ERROR ScreensAllscreensreadstatusas“No”undernormalcondition
30 STATUS/FX/WARN-------------P00acin freq Notoo low DOWN UP TOP PORT STATUS/FX/WARN-------------P00acin
31STATUS/FX/DISCON-----------P00 acin freq Notoo high DOWN STATUS PORT STATUS/FX/DISCON-----------P00 aci
32INSTALLATION DRAWINGA 30A input breaker (maximum) must be •used with the AC sourceA 30A breaker (maximum) must be used to •protect the output circ
33INSTALLATION CHECK LISTITEM
34OBX-IC2024S-120/60 Inverter/Charger Specications Nominal DC Input Voltage Range 24 VdcNominal AC Voltage / Frequency 120 Vac / 60 HzContinuousP
35AC Input Operating Voltage RangeNote: This is the recommended AC input voltage range to be supplied to the Inverter. Voltages outside of this range
36INVERTER DEFAULT VALUES (subject to change with upgrades)24 VDC System DEFAULT MINIMUM MAXIMUMFloat Voltage 27.4Vdc 24 Vdc 30 VdcAbsorb Voltage 29
37MaintenanceFollowing exposure to salt water, rinse all exposed surfaces to prevent corrosion. Recoat the DC lugs •and other exposed conductors wit
2Welcome to the OutBack Extreme Rugged Water Resistant Inverter/ChargerThe OutBack Extreme Rugged Water Resistant Inverter/Charger (hereafter called t
381-Year Limited Warranty OutBack Extreme Inverter/ChargersOutBackPowerSystems,Inc.(“OutBack”)providesaoneyear(1)limitedwarranty(“Warranty
39After receiving the RMA number, pack the Product(s) authorized for return, along with a copy of the original purchase invoice and warranty certicat
40OUTBACK EXTREME INVERTER/CHARGERLIMITED WARRANTY REGISTRATIONComplete this form and return it to:OutBack Power Systems Inc.19009 62nd Ave. NE • Arli
41
Corporate Headquarters1900962ndAvenueNEArlington,WA98223USAPhone:(+1)360.435.6030www.outbackpower.com900-0046-01-00REVAEuropean Sales Oce
3Parts IncludedStandard with the OutBack Extreme Rugged Water Resistant Inverter/Charger, Model OBX-IC2024S-120/60:• OneOwner’sManual• OneDCCove
4 R EA D FIR ST ! SAVE THESE INSTRUCTIONSRead all instructions and cautionary markings on the Inverter, the batteries and all appropriate sections of
5Designthebatteryenclosuretopreventaccumulationandconcentrationofhydrogengasin“pockets”atthe top of the enclosure. Vent the battery com
6MOUNTINGTheInverterweighs57.5lbs(26.08kg)andmustbesecuredwithappropriatefastenerstoasturdy•mounting surface capable of supporting i
7The equipment ground on each is marked with this symbol: Box lug for grounding the Inverter chassisSYSTEM PROTECTIONElectrical systems are designe
Comments to this Manuals